Century Premium Tyres in Brunswick East | Automotive repair centre

Century Premium Tyres

Locality: Brunswick East

Phone: +61 3 9388 8870

Address: 370 Lygon Street 3057 Brunswick East, VIC, Australia

Website: http://centurytyres.com.au

Likes: 172

Add/Update information

Reviews

Tags

• Automotive, aircraft & boat
• Automotive repair centre
• Tyre dealer & repair shop

25.01.2022 https://au.vehiclevisuals.com//getAnimationLi/1q5nrr8y217x Tyre Rotation Tyres tend to wear unevenly between the front and rear, and even side to side. To maximize tread life, your tyres should be rotated to a new position on the vehicle every 8,000~16,000km or according to your vehicle manufacturers recommended interval.... * Tyre wear rates are affected by the configuration of the vehicle, but also by these contributing factors : - acceleration (increases wear on the driven wheels) - braking (biased towards the front wheels) - steering Each corner of the vehicle has a slightly different weight load, which results in variations in the tyre wear rate. By rotating your tyres regularly you can even out the front and rear wear patterns. ** Front wheel drive vehicles : the front tyres -> rear the rears -> front (without changing sides) ** Rear wheel drive vehicles : the front tyres -> rear (sides are switched) the rears ->front (on the same side) ** 4WD or AWD vehicles : the front tyres and rear tyres are rotated diagonally. With the wheels installed and the vehicle on the ground, the wheel nuts are tightened to the correct specification using a torque wrench. The tyre pressures are adjusted as required since inflation pressures are often different for front and rear tyres.

24.01.2022 https://au.vehiclevisuals.com//getAnimationLi/3i824g6bqe53 Spark plug The spark plug ignites the fuel/air mixture inside the combustion chamber. A normal spark plug appears grayish-brown in color and has sharp or just slightly rounded edges on the electrode.... A lot can be determined from analyzing a spark plug from a vehicle. A normal spark plug will appear grayish-brown on the electrode and ground strap. This indicates that the fuel system and ignition system are properly tuned.

24.01.2022 During cold weathers your car Heater Matrix is sure important to keep you warm during your travel. Check the short video below to know more about it https://au.vehiclevisuals.com/animation_link.php

24.01.2022 Symptoms of faulty suspension and/or steering systems 1. Nose dives, squats or rolls when your car nose dives forward, squats backwards or rolls from side-to-side when you move in different directions. 2. Bottom out when your car doesnt have enough suspension to absorb the bump it is driving over and the tyres hit the bottom of your car when the suspension is compressed. 3. Bouncing over bumps when your car bounces repeatedly after driving over a bump in the r...oad. 4. Bumpy ride - when you can feel every bump in the road. 5. Bump steer this happens when your car hits a bump and the wheels turn left or right without the driver turning the steering wheel. 6. Oversteer / Understeer when the rear or the front of your car loses traction when rounding a corner. This is worse when road surfaces are slippery. 7. Hard steering / power steering doesnt seem to be working this is when it becomes more difficult to turn your steering wheel. 8. Loose steering the opposite of hard steering above, steering is now too easy and feels sloppy. 9. Car pulls to one side when driving / car seems to wander down the road this is often only noticed when the problem becomes severe. When driving, you need to hold the steering wheel in place in order to keep your car going in the right direction. 10, Steering wheel jerks while you dont notice any (or many) other problems, your steering wheel seems to jump or jerk at irregular intervals. 11. Steering wheel vibrates from 72 km/h (approximately 45 mph) your steering wheel and car start to vibrate. 12. Steering wheel wobbles your steering wheel starts to wobble from side-to-side when you drive at a constant speed. 13. Noises when turning a corner the only symptom you notice is a knocking, clunking and/or squeaking noise when you turn a corner. 14. Noises from the power steering unit the only symptom you notice is a whining noise from the steering when you turn the wheel fully in one direction or the other. 15. One low corner in other words you notice one corner of your car is lower than the others when it is unloaded and parked on even ground. See more

23.01.2022 https://au.vehiclevisuals.com//getAnimationLi/3r6jd7qat5zw Check out the video about Rear Differential The rear differential transmits torque from the transmission to the rear wheels of the vehicle.... The rear differential normally consists of a pinion gear, a ring gear, two spider gears and two side gears. The two side gears are connected to the axles which drive the rear wheels. When the vehicle is traveling in a straight line, the pinion gear transfers power to the ring gear which then transfers power to the side gears. When the vehicle is cornering, the wheel on the inside of the corner is traveling a shorter distance and therefore needs to be able to turn slower than the wheel on the outside of the circle. When this happens, the spider gears rotate and allow the side gears to travel at different speeds.

22.01.2022 For a smooth ride, get to know how suspension works!

21.01.2022 http://tinyurl.com/qpkabqx What are "control arm bushings" and why are they important? Rubber bushings are used in areas where suspension components meet, such as where the control arms attach to the subframe. ... The rubber absorbs shocks from minor road imperfections while allowing some movement between components. With constant movement and flexing, rubber bushings can wear out. Rubber also deteriorates with age even when the vehicle is not being driven. Worn Control Arm Bushings can reduce ride comfort and increase road noise. As bushings become more worn, wheel alignment angles can be affected, accelerating tyre wear. Therefore, control arm bushings are to be inspected as part of a routine maintenance plan and replaced when found to be worn

19.01.2022 Winter is over As we are emerging from a rather rough winter, its time to gear up for the spring and summer months ahead. One of the most important things to get ready for warmer weather is your automobile. Winter could have cause changes or damages to different parts of your automobile. To ensure your safety, dont forget to do your car maintenance spring check Check the video below for further details ... http://tinyurl.com/y4o39p9r See more

19.01.2022 Notice to all customers regarding COVID-19 restrictions Wed like to clarify that our business is still allowed to operate in accordance with the updated COVID-19 restrictions and no customers will be penalized for using our service. Refer to the letter below for the details.... Stay safe. We are all in this together. See more

18.01.2022 https://au.vehiclevisuals.com//getAnimationLi/wyc5ydb0oj6n Brake Systems The purpose of the system is to convert the energy of the moving vehicle into heat in order slow the vehicle down. Although some hybrid vehicles are beginning to convert kinetic energy into stored electricity, all vehicles still use a brake system similar to that shown here.... The pressure from the drivers foot (with assistance provided by the vacuum booster) is initially converted into fluid pressure in the brake lines by the brake master cylinder. Brake fluid is a hydraulic fluid that is stable in volume under a wide range of temperatures - it does not expand as it heats up.The pressurized brake fluid forces the pistons in the brake caliper outwards, so that they press against brake pads. The pads squeeze the surface of the rotating brake disc, causing it to slow, and generating heat. The heat is dispersed through cooling fins inside the rotor to prevent the rotor and pads from overheating. Most vehicles also have an ABS system - designed to pulse the brakes on a skidding wheel when maximum braking pressure is applied.In damp climates and areas where salt is used to de-ice roads, the metal brake lines can become rusted. Failure to replace rusted brake lines can result in the line rupturing under pressure, allowing the brake fluid to leak out of the system

17.01.2022 https://au.vehiclevisuals.com//getAnimationLi/yc8y7f1j9no6 Warped Brake Disc Brakes are designed to convert movement energy into heat in order to slow and stop your vehicle. The friction material on the brake pads wears off over time, but replacing brake pads alone is not always enough to maintain efficient braking. ... Under certain circumstances, such as extreme braking followed by prolonged pressure between the brake pad and hot disc, some of the friction material from the pad can become embedded into the surface of the disc. This causes the disc to have uneven thickness. The warped effect on the disc can cause the steering wheel to shake and the brake pedal to pulse - especially under heavy braking.

16.01.2022 Winter is here! As evenings begin to get darker earlier and the weather gets colder, roads can be hazardous and we need to be confident that our vehicles are safe and reliable for the season. As the temperature drops, it is imperative to to keep an eye on the key issue areas it impacts. Even if you feel as though your car is running perfectly fine, it is always a good idea to get a Winter Check before you go into the colder months, as there can be problem areas that you may ...not be aware of. Check the video below to know further about winter check ;) https://au.vehiclevisuals.com/animation_link.php

16.01.2022 Notice to all customers regarding COVID-19 restrictions We'd like to clarify that our business is still allowed to operate in accordance with the updated COVID-19 restrictions and no customers will be penalized for using our service. Refer to the letter below for the details.... Stay safe. We are all in this together. See more

16.01.2022 http://tinyurl.com/u2xhxx5 Do you guys all know how the clutch system works? Heres a simple video demonstrating it. Friction material on clutch eventually wears out, and slipping clutch is the first notice on a high gear.... get knowledgeable on which parts should be replaced in this case

15.01.2022 The cabin air filter is usually located just before or after the blower motor of the vehicle. It filters out dirt and contaminants entering the vehicle and also filters out unpleasant odors. The cabin air filter should be checked regularly. The cabin air filter is usually located under the hood, near the windshield or under the vehicles dashboard, near the glove box. It filters the air as it is drawn in by the blower motor. The filter mechanically filters dirt and particles ...entering the cabin of the vehicle, but it also contains a layer of carbon that filters out unpleasant odors. A cabin air filter that is plugged will decrease the flow of air through the air vents. Check the video below to know more about Pollen Filter!! http://tinyurl.com/yy3lqz4c

13.01.2022 https://au.vehiclevisuals.com//getAnimationLi/gxkqb7gdxmlq Hi everyone, today we brought a topic of turbo oil leak. The turbocharger increases the density of air entering the engine by using moving exhaust gases to compress air entering the intake. ... As a result, the engine management computer is able to deliver more fuel to each cylinder creating more engine power from the same amount of engine displacement. Compressing air creates large amounts of heat, therefore turbochargers have multiple oil and coolant passages running through them to lubricate and cool the moving parts in the turbo. Seals throughout the turbo keep these fluids from leaking into the air intake of the engine. If a seal inside the turbo fails, oil can leak past the seal into the air intake of the engine. This causes the engine to burn excessive amounts of oil and normally plumes of blue smoke can be seen exiting the tailpipe. Any type of oil leak should be taken care of immediately as low engine oil levels will cause damage to the engine. If you have any comments to say, its welcomed. Also visit us on our website https://www.centurytyres.com.au/ for more mechanical information.

12.01.2022 https://au.vehiclevisuals.com//getAnimationLi/3l2e88ny9bwa Timing Belt The timing belt assembly consists of the timing belt, belt guides and the timing belt tensioner.... When a timing belt breaks the intake and exhaust valves become bent as they collide with the piston and may get stuck. The Timing Belt connects the crankshaft at the bottom of the engine with the camshafts at the top of the engine. The teeth on the belt and on the crankshaft and camshaft sprockets, ensure that the valves open and close at exactly the right times. The intake valve opens to allow fuel and air into the cylinder, then closes as the mixture is compressed, then ignited, then the exhaust valve opens to allow the waste gases out. Timing belts are lighter, quieter and more fuel efficient than metal timing chains, but require replacement at manufacturer recommended intervals. If the belt breaks when the engine is running, it is possible that valves can become stuck in the open position, and bent by contact with the piston. Replacement of bent valves involves a significant amount of labour as the engine needs to be disassembled to remove the cylinder head, replace the valves, repair any other related damage and resurface the cylinder head before reassembly. During a routine timing belt replacement, the hydraulic tensioner and the pulleys that keep the belt tight should also be replaced, along with the coolant pump where it is driven by the timing belt, to prevent future failure as a result of reusing worn parts.

12.01.2022 https://au.vehiclevisuals.com//getAnimationLi/v47tkj565zhg Heater Blend Door Actuator The blend door actuator is an electrical motor connected to a series of different gears to multiply torque.... Technical Description Once the temperature controls are changed, the blend door actuator receives a signal to rotate the blend door to a specific position. Once that position is reached, the blend door actuator stops until the temperature controls are changed again.

11.01.2022 Electromechanical Parking Brake (EPB) systems include all the normal parts of a disc brake system, but also include an electric motor connected to the brake caliper. Technical Description Some newer vehicles with disc brakes on the rear as well as the front incorporate an electromechanical parking brake or EPB. Unlike conventional drum style parking brakes, EPBs apply the disc brake to hold the vehicle in place when it is parked. Vehicles with an EPB system use an electrical... switch to apply the park brake instead of a lever or park brake pedal, and the brakes are usually applied automatically when the vehicle is turned off. The electric motor connected to the brake caliper spins in order to apply and release the parking brake. CHECK THE VIDEO BELOW FOR FURTHER INFORMATION :) http://tinyurl.com/y5w8mctd See more

11.01.2022 https://au.vehiclevisuals.com//getAnimationLi/pvwtsfebgrzh . Plugged Oil Filter Oil Filters come in two different styles -- cartridge and spin on. ... With a spin-on type oil filter, oil enters the small holes surrounding the main centre hole. The oil then passes through a filter element that removes any foreign particles that could harm the engine. Oil then returns to the engine through the large centre hole at the top of the filter. If an oil filter becomes plugged to the point that oil does not flow quickly enough, oil will travel around the filter element through the bypass valve. This ensures that the engine will be lubricated, even when the filter is plugged, however, any particles in the engine oil will not be filtered and will increase the wear rate of the engine.

09.01.2022 https://capricorn.vehiclevisuals.com/animation_link.php

09.01.2022 Have you check your car drive belt? Remember! Driving on an old belt is a disaster waiting to happen because it powers most all of an engines accessories. When your belt breaks, slips and, ultimately, wears out, everythingfrom the power steering pump to the alternator and air conditionerstops working. Whats more, the parts it controls can become severely damaged. By replacing your belt periodically, you can minimize the risk of breakdown. For more information check this ...video! :) https://capricorn.vehiclevisuals.com/animation_link.php See more

09.01.2022 https://au.vehiclevisuals.com//getAnimationLi/en01pxktl0np Whats up guys? Today, Wed like to share a post about tread separation of tyres.... The tread of a tyre refers to the rubber compound that surrounds the circumference of the tyre. The tread is bonded to the steel belts directly underneath. Tyre tread is usually grooved so as to displace water while driving as well as provide traction on loose surfaces. Certain precautions must be taken in order to assure that tyres wear properly. Tyre separation is a condition when the tread becomes separated from the steel belts. It normally creates a bump in the tread, and can be heard as a thumping noise while driving. Once tyre separation is detected, tyres should be replaced immediately as it is a potentially dangerous problem. If you have anything to comment, please go for it, and well reply it with sincerity.

09.01.2022 The steering and suspension systems are important for both your safety and comfort when driving as they ensure a smooth ride as your car travels over bumpy roads. The two systems are usually talked about together as they are directly related to each other. Its a good idea to schedule regular inspections of your steering and suspension systems. It is usually easier, cheaper and safer to discover and fix a problem before it obvious and severe It is best to get your steering an...d suspension systems inspected. - Every 50,000 miles (approximately 80,000 km). - When your tyres are replaced. - When your brakes are serviced. - When your oil and filters are changed Click this link to watch a video about steering inspection: https://au.vehiclevisuals.com/animation_link.php

09.01.2022 https://au.vehiclevisuals.com//getAnimationLi/u71zwcb4vzqy Manual Drivetrain The manual drivetrain comprises the clutch system and the manual transmission. The clutch system includes a flywheel, clutch disc and pressure plate. The clutch disc drives the input shaft of the transmission.... When the clutch is engaged, the clutch disc is squeezed between the pressure plate and flywheel, and power is sent to the transmission. When the clutch is disengaged, the pressure plate moves away from flywheel, so that the engine can rotate the flywheel and pressure plate without turning the clutch disc. This allows the engine to run without transmitting power to the transmission. The manual transmission includes gears, synchronizer rings, shift forks and bearings, and alters the ratio between one rotation of the engine and the number of rotations of the wheels on the vehicle. This makes the engines powerband more useful when driving.

08.01.2022 https://au.vehiclevisuals.com//getAnimationLi/mz66oxv5hqqy Heating / Aircon The heating system consists of hot coolant from the engine, a heater core and a blower motor. The A/C system consists of an A/C compressor, condenser, evaporator core, expansion device and receiver/drier. The heater removes heat from the cooling system and adds it to the passenger compartment. The A/C system removes heat from the passenger compartment to outside the vehicle.... Technical Description In order for the heater to function, hot coolant passes through the heater core. Cool air is blown through the heater core and heat is transferred from the heater core to the air. The heated air is then circulated through the desired vents and into the passenger compartment. The small tubes and fins of the heater core create a large surface area for the air passing through the heater core.For the A/C system, freon gas is compressed by the A/C compressor. The high pressure gas is then changed to a high temperature liquid inside the condenser as air blows through the condenser. The liquid then moves to a metering device. As it passes through the metering device to a lower pressure, the liquid evaporates and cools. This cool gas then passes through a series of coils also known as the evaporator core. After passing through the evaporator core, the low pressure freon gas returns to the compressor. The blower motor blows air through the cold evaporator core, removing the heat from the air. This cool air is then directed to the desired vents and into the passenger compartment.

08.01.2022 https://au.vehiclevisuals.com//getAnimationLi/7mxrw53o8077 Accessory Drive Belt System A drive belt mechanically powers the accessories in the engine bay.... As a drive belt wears over time, the teeth rest in the grooves of the belt rather than on the surface. The accessory drive belt is made of a synthetic rubber compound and drives accessories on the vehicle such as the alternator, power steering pump, and air conditioning compressor. The belt tensioner puts tension on the drive belt to keep the belt in place and to create sufficient friction to turn all the pulleys on the belt system. Recent technology improvements in belt construction mean that belts do not develop cracks, even when they are worn. A new belt will come in contact with the drive pulley on the sides of the ribs only. As the belt wears, the ribs become thinner and thinner and when the belt is completely worn, the belt rides on the peaks of the drive pulley. This reduces the grip between the belt and pulley and causes the belt to squeal. When the belt tensioner becomes weak, the belt is not wrapped tightly enough around the pulleys, potentially resulting in slipping, especially on components that require a lot of energy to rotate, such as the alternator. This can result in squealing noises and reduces accessory efficiency. A misaligned belt tensioner - where the surface of the tensioner pulley doesn t run parallel with the belt and other pulleys - can occur with automatic spring tensioners. The misaligned tensioner pulley puts greater pressure on a small section of the belt, which eventually causes a rib or multiple ribs to become detached from the belt. Idler pulleys are used to route the belt to the different components of the accessory drive belt system. Inside the pulley is a sealed bearing which can eventually fail. A failed bearing causes the pulley to stop turning. The rotating belt rubs against the seized pulley surface, generating a lot of heat and noise until the belt breaks. With a broken belt, the vehicle can become undriveable.

06.01.2022 https://au.vehiclevisuals.com//getAnimationLi/q64c4kz7cyh0 Given the circumstance of nation-wide shutdown, vehicles got to play crucial role in every business. Have more knowledge on your car to drive safe by checking our weekly post! Suspension System... the basic function is to keep the tyre in contact with the road at the correct angle while absorbing bumps and road imperfections. Commonly used components include : ball joints (which allow components to rotate and change angle), springs, shock absorbers or dampers (that limit the rebound of the springs), rubber bushings (that absorb shocks while allowing some movement), and anti-roll bars with their linkages, (that limit the amount of vehicle roll during cornering). How can the suspension system fail? The lining that keeps ball joints tight wears out over time, or can be damaged by frequent rough road use. Rubber bushings also wear out over time. The valves inside shock absorbers or dampers flex constantly as the vehicle is driven. When the valves are weakened with use, the dampers stop controlling the spring movements effectively. Results of failure Worn suspension components such as ball joints, rubber bushings and shock absorbers can increase road noise, reduce ride quality and affect the wheel alignment, potentially causing accelerated tyre wear. Required Service or Repairs Suspension components should be inspected as part of a routine maintenance plan and replaced when found to be worn We are operating as normal, so if you face any issue with your car, well be able to help you. Everyone stay safe, and well be back next week with different topic

06.01.2022 https://au.vehiclevisuals.com//getAnimationLi/b7wscl292teq On car brake lathe Brake pedal pulsation is most often the result of uneven thickness in the brake disc. This thickness variation can be the result of friction material becoming embedded in the disc, or as a result of a section of the disc wearing down through repetitive contact with the brake pads.... Although all vehicle parts are manufactured within tight tolerances, where multiple connecting parts each have a small variation that is within the acceptable manufacturing tolerance, the combined variations can result in a disc that does not spin completely straight, even when the disc may be perfectly aligned when measured off the vehicle. Resurfacing the brake disc with it installed on the vehicle using an on-vehicle brake lathe ensures that the brake disc matches perfectly with the other vehicle components for smoother braking and longer brake part endurance.

05.01.2022 https://au.vehiclevisuals.com//getAnimationLi/ld0z5fn5fhvp Punctured Tyre on Sidewall A radial tire is composed of the tread, shoulder, sidewall, bead and several plies. The sidewall connects the tread of the tire to the bead and allows the tire to flex when hitting a bump in the road. A punctured tire can be repaired as along as the puncture is within the tread section of the tire.... Tyre treads are constructed with multiple layers of rubber with steel belts and polyester or Kevlar cords that provide a very strong structure. The sidewall needs to be much more flexible, and consists only of rubber and radial plies - so any damage to the sidewall will weaken the structure of the tyre. Repair plugs are designed to stop air leaking, but since an attempt to patch the sidewall will not repair the damaged structure of the tyre, the tyre would remain susceptible to a blowout.

05.01.2022 Check out the video below to know more about spark plugs! https://capricorn.vehiclevisuals.com/animation_link.php

05.01.2022 https://au.vehiclevisuals.com//getAnimationLi/hqkiwjwcqzk2 Hey guys, today weve got contents to enhance your understanding of wheel alignment. The alignment angles mainly consist of toe, camber and caster.... The toe alignment angle determines where the tyres are pointed in relation to each other. It is usually adjusted by the track rods. Vehicles with excessive toe in or toe out can experience rapid tyre wear and may also experience feathering of the tyre tread. The camber angle is the angle that the tyre makes relative to vertical. Excessive camber in either direction can cause tyre wear on just one edge of the tyre and can create a pulling force that will cause the vehicle to drift as it moves down the road. Camber angles are especially affected by the suspension components. Worn suspension springs and shock absorbers allow the vehicle to sit lower, causing negative camber. The caster angle is the angle between vertical and the steering pivot axis. Caster can be adjusted by moving the top of the struts forward or rearward. Caster angles that are out of adjustment usually wont cause tyres to wear, but may cause the vehicle to pull if caster angles differ greatly between the two front wheels. Caster can also affect the steering effort

04.01.2022 We hope, Everyone is safe in this uncertain times. Thankfully we are still open, We can still help you if youre car is not running well

03.01.2022 Get to know more about car Oxygen Sensor. Check the video below Oxygen sensors are designed to maintain optimal fuel efficiency for continuous performance. An oxygen sensor continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicles ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal ...AFR. **When you have a bad oxygen sensor, your vehicle will run less efficiently, it can sometimes have a poor idle, erratic jerking at steady throttle, hard starting problems, cause the check engine light to come on, and will cause high fuel consumption.** http://tinyurl.com/y6jajv6a

03.01.2022 https://au.vehiclevisuals.com//getAnimationLi/aavv37g35chg Good morning Century Tyres family Lets start the week with lots of cheers and energy!... Speaking of which, its the engine that is crucial to convert energy to mechanical motion in cars. In what type does it come? - Spark Ignition engines, which burn petrol or ethanol - Compression Ignition engines, which run on Diesel fuel. What are the components? Engines are mainly composed of the engine block, crankshaft, connecting rods, pistons and cylinder head. Also theres another significant part named timing belt which ensures the action of the valves and pistons is synchronised. Motor mounts keep the engine from twisting from the torque of the engine, as well as absorbing vibrations. Engines are filled with oil to keep moving parts lubricated and cooled, and use various gaskets to keep the oil from leaking out. On most vehicles, accessories such as the alternator, power steering and air conditioning are powered by the engine using drive belts. How does it works? The internal combustion engine uses hot expanding gases to push against the piston. The downward movement of the piston is converted to rotational movement by the crankshaft. It is then directed to the rear wheels of the car. Essential parts of the engine, like the timing chain and timing belt synchronize the timing of the crankshaft and camshaft. The engine rotates the accessory drive belt system in order to provide energy to systems like steering and HVAC. Comments, sharing are always welcome. Any inquiries, feel free to reach us on 9388 8870 or our website https://www.centurytyres.com.au/ Have a wonderful week everyone and well come back next week with other interesting topic

02.01.2022 https://au.vehiclevisuals.com//getAnimationLi/wl8mtsiukvb9 Axles & Driveline Components of the driveline are designed to smoothly transmit the rotating power of the engine, while still allowing suspension to flex and wheels to alter direction. ... Front wheels are usually driven by an axle that includes constant velocity, or CV, joints. Differentials allow for the turning rate of a pair of wheels to be different, which is necessary during cornering. Four wheel drive vehicles have two differentials, one for the front wheels and another for the rear wheels. A transfer case is a switchable gearbox that delivers power to the front and rear differentials. The transfer case is connected to the differential by the driveline. All wheel drive vehicles use a similar concept, however the transfer case is replaced with a centre differential, which usually allows more or less engine power to be delivered to each axle

01.01.2022 Have you ever wondered when getting two new tyres why they are installed on the rear wheels? Lets find out by discussing skid condition and acqua planning. Check out the video.... https://au.vehiclevisuals.com//getAnimationLi/r4h87ljg5880

01.01.2022 The South Australian coroner has issued a warning to the public following the death of a man on a farming property while he was inflating a tyre. David Whittle says split rim or multi-piece rimmed tyres can explode - causing serious injuries or death when being inflated without proper precaution. Safework SA says the incidents happen every year, prompting a reminder to those inflating tyres of the risks when doing so. Split rims are commonly found on forklifts, earth-moving... machinery and wheelbarrows. Theyre also used in heavy vehicles, like trucks and buses and are different from regular wheels found on most cars because the rim is made up of multiple parts held together by bolts or a lock ring. Advice on how to stay safe includes deflating tyres before removing them, checking for any signs of damage, having a safety cage, and using a long air hose, so you can stand well clear when inflating. The family of the man killed did not want an inquest into his death, instead, pleading with others to take extra care. See more