Evolution Custom Touring Solutions in Baldivis, Western Australia | Automotive repair centre

Evolution Custom Touring Solutions

Locality: Baldivis, Western Australia

Phone: +61 400 996 017

Address: 25 Pymmes Junction 6071 Baldivis, WA, Australia

Website:

Likes: 142

Add/Update information

Reviews

Tags

• Automotive, aircraft & boat
• Automotive repair centre

24.01.2022 Hope everyone had a Happy Easter! Ours was spent getting this RG Colorado ready for a trip back east! We Installed a suspension upgrade from TJM, new rims and tires from Jandakot Tyrepower, fixed some broken tray mounts and also identified and rectified a few electrical issues. Now it’s set up for the trip back east along the beach through Cape Arid National Park

24.01.2022 Everyone loves goodies day!, shoulda cleaned the water tank

23.01.2022 Pre fit and wiring done!, getting there now, couple of small little fab bits and a few welds and we’ll be ready to coat this in Raptor!

18.01.2022 When putting photo A, on this Senator in photo B, I suggested putting photo C in to avoid the costly rear brake pads in the future! Needless to say it was not really required and the owners declined, oh well

18.01.2022 After getting a call out on Saturday to replace an alternator on a Pajero I tested the battery, starting and charging systems. What the internet had said was a faulty Alternator, was in fact just a dodgy earth terminal. Needless to say the diagnostic equipment had identified the fault and saved this particular customer hundreds in a pointless repair bill. With up to date software and training we can help with any electrical or mechanical faults hit us up if your check engine light is showing and we will be more than happy to help. We are a qualified repairer too

17.01.2022 Ford PX Ranger dual batt system mounted underneath the rear seats, if your only using the system every now and then this is an in-obtrusive option!

16.01.2022 Remember this Rig!

15.01.2022 This is what I found underneath a customers car!, when he saw what we had done with his Ultimate dual battery system, to say he was excited was an understatement, he actually wanted to pull this system out of his old ranger and put it into his PX II!

14.01.2022 Slowly getting images to upload, here’s where it all began!, I bought this from the Eastern States as a blank canvas, turned out every accessory that was fitted needed to be re-wired. We turned a dual battery system into a triple with custom battery trays and where able to keep the fridge running for a bit longer than a day. All before DC DC chargers where all to common

13.01.2022 Bit of Fabrication to facilitate a Tow pack for a 200 series, relays to control spotlights and Anderson Plug, circuit breaker for brake controller and fuse block for your basic accessories

11.01.2022 Well before the boss comes home tomorrow, I managed to put this little jigger back together this morning! All though I did spend most of last night throwing clear coat at it, it came out like a sheet of black glass! Now I gotta hide it till the Easter Bunny comes. Should be a good chook chaser down the skate park for Dad when he gets his new one! #HavntRiddenAPushyIn20BloodyYears! #ThisMightHurtMoreThanThe450

10.01.2022 Well now that most of the fab work is out of the way it’s now time to join all the dots! Seems it’s going to be done under lights I thought I better put a bit of etch primer on it to full the reflection

10.01.2022 One of the first canopy set ups I done, things have changed ALOT since then!

08.01.2022 Something Big! is going to happening to this all ready kitted out PX II Ranger! Work is starting next week on decking out the rear to make camping and days out bush a whole more comfortable for the family! Make sure you follow this one, as apart from a few parts here and there it’s ALL CUSTOM!!!!

08.01.2022 Well the back end is stripped and fabrication starts tomorrow

07.01.2022 Something apart from 4wd’s!, this was a battery relocation to the other side of the engine bay to accommodate a bigger air intake for the turbo, it also required a radiator overflow relocation. While we were at it we installed a crank case and PCV catch can mounted to the new battery box and modify the factory BOV plumbing, #ZEROFG

06.01.2022 Basic wiring loom construction, it’s in the components and finish that set us apart from others, Good Work isn’t cheap!, Cheap Work isn’t Good!

04.01.2022 I set the rear of this good ole bus up to be as self sufficient as could be back in the day, by moving all the hardware to the back of the car allowed us to share power and air with the camper, this kind of setup is now the norm! Pioneering anyone?