FAB LAB | aircraft & boat

FAB LAB

Phone: +61 421 710 904

Add/Update information

Reviews

Tags

• Businesses
• Vehicle, aircraft and boat
• Automotive
• aircraft & boat

25.01.2022 not far off startup now , we have been super busy and we are sorry if we have been slow to reply to messages and have been slack on the page updates, for a faster reply give me a buzz or shoot me a SMS

25.01.2022 congrats to jamie for completing drag challenge on the weekend doing over 1000k's finishing 7th overall out of 130 entrants and running a PB of 8.7@156 aswell as a string of 8 sec passes

24.01.2022 Bit more progress on the cosworth powered escort with a Custom cooling setup all wrapped up on it. We made a custom intercooler with inlet/outlet in engine bay, custom dual pass radiator, fan shroud with a big spal fan, converted the intake manifold to DBW, plazmaclamps throughout, custom intercooler pipes, custom intake pipe with inner guard bezel, airbox in the inner guard area, custom header tank, custom radiator overflow tank hidden under the inner guard with lid in engine bay, waterpump blanking plate to covert to EWP setup, modified the top water neck for AN

24.01.2022 32 GTR back from 101 motorsport for a new 4" stainless exhaust with magnaflow muffler to join upto the 4" dump we previously did some time ago to replace the old jap system

24.01.2022 32GTR we had in for a custom 3.5" stainless exhaust system, plumb the wastegate in, mount intercooler, custom intercooler piping, custom power steer resivior, rad overflow tank, catch can, battery mount and air filter partition shroud

23.01.2022 Veilside R32 GTR finished up that was in for a custom split pulse exhaust manifold with EGT provisions, A pair of 40mm turbosmart wastegates, borgwarner EFR9180 turbo, 4" stainless dump pipe joined to the existing exhaust system, stainless screamer pipes, intake pipe and join to the existing intercooler piping

23.01.2022 LSA S15. we did front tubs, mount engine and gearbox, trans tunnel, willwood clutch pedal under the dash, custom sump, modified the crossmember, custom headers, stainless twin 3.5" exhaust into a single 4" with a magnaflow muffler, catch can, intake pipe, partial engine bay shave. off to get the bay painted and put together by the boys at 101

22.01.2022 Turbo seadoo with the lot

22.01.2022 ceffy in for plazmaclamps, custom intercooler piping, intake pipe, custom catch can and a stainless 3.5" dump pipe

22.01.2022 Custom 4G63 big runner, twin scroll, twin wastegate manifold for a #jhhracing billit block motor headed for hong kong

20.01.2022 S14 rollcage and removable parachute setup all finished, cars off now to get custom trimmed interior

19.01.2022 We had a huge year this year! A massive thankyou to all of our customers for all your continuous support and we look forward to building more badass cars in 2019!!! we wish everyone a merry christmas and a happy new year. stay safe

18.01.2022 Mitchs 1200 wagon rollcage and parachute all finished up, we have finished majority of all the other fabrication on this car but will post more pics at a later date

18.01.2022 180sx was in for a weld in half cage and setup velo drivers harness

18.01.2022 Wrx we had in for a custom twist mount turbo setup. We fabricated a custom up pipe, 4" custom full stainless exhaust system with the wastegate plumbed in, magnaflow muffler and a "cat body", we flipped the standard intake manifold around to be forward facing, fit new process west intercooler, all new intercooler piping, intake pipe, custom alloy radiator header tank, 2 in 1 catch can/rad overflow tank,

17.01.2022 sweet pic from sydney powerplay on the weekend, we made the trek down with adams 1200 and ryans s14. sydney powerplay knows how to party, deffinatly back for the next one

17.01.2022 fit N/A 2j into this 77 cressida wagon, custom engine mounts, custom gearbox mount, custom auto linkage to use standard shifter, modify standard headers and full 2.5" mild steel exhaust system

16.01.2022 sneak pic of a S15 we have been doing a conversion on and a big list of other things

16.01.2022 subaru racecar in for a twist mount turbo setup, custom up pipe, new hot side intercooler pipe, 3.5" stainless dump pipe, plumb the wastegate into dump pipe, 3.5" front pipe into existing Ti system, custom intake pipe

16.01.2022 subaru H6 twist mount turbo setup, stainless crossover, stainless up-pipe, 3.5" dump pipe with a variable wastegate pipe for screamer and plumb in, 3.5" exhaust into twin 3" at the back with a pair of magnaflows, join up to existing intercooler piping and an intake pipe... pipework galore Diversion Garage

16.01.2022 Guys gtx55 barra powered KE20 corolla we finished all the fabrication on. everything kept under bonnet. Massive list of things carried out on it- mount engine and gearbox, new firewall, removable trans tunnel, tube front end, tube arms, rack conversion, custom made intercooler, custom radiator, engine bay bars joining to existing cage, promod style manifold, 5" dump pipe, stainless side pipe, stainless seperate exhaust system, custom tanks, spew tank, removable pedal box, custom steering colum, anti roll bar.. no doubt alot more ive forgotton.

16.01.2022 4 rotor FD rx7 project we have had on the go and can Finally let some pics slip with a pair of precision 7275s onboard

16.01.2022 2J jzx100 was in for custom engine mounts, custom exhaust manifold, 4" stainless dump pipe, 3.5" stainless dump back exhaust system, mount intercooler, intercooler piping, intake pipe, swirl pot, powersteering resivior, windscreen washer tank, radiator top pipe, modified lower radiator pipe neck

16.01.2022 RS260 stagea in for a set of twin 3" stainless front pipes, 100 cell cat into a single 3.5" stainless exhaust

16.01.2022 andra 6 point rollcage with removable intrusions, waiting for some new carpet then re assemble all the trim

15.01.2022 Had jamies commodore in for a heap of stuff to get it ready to go racing. did a full weld in cage with removable intrustions, removable parachute setup and also tow bar, mount kirky seats, setup simpson harness, fit enemys everywhere anti-rollbar kit, external battery isolator with pull knob under tail light, engine containment tray, engine spew tank in the boot and plumb it up, alloy battery mount, fuel pump mounts, tailshaft loop, re mount the fuel cell, mount the parachute lever in the factory handbrake hole... and a few other small things.. now off to finish the cage getting painted and interior back in

15.01.2022 More progress on the twin turbo Quad rotor project with the Cooling system all wraped up. Starting off with PWR cores we custom made the radiator, oil cooler and intercooler. Also got the dump pipes and screamer pipes finished up.

15.01.2022 finished up this bolt in half cage for stehpens DC5 integra

14.01.2022 BLKRICE GTR was in for a chromoly rollcage with removable intrusion bars, removable parachute setup, fit kirky seats and simpson harnesses, fit monster 165mm thick intercooler and modify pipework to suit, engine containment pan, tailshaft loop, engine spew tank and a front tow hook

14.01.2022 Had this beautiful FD RX7 in for a complete hot side whilst keeping everything still legal

14.01.2022 we are super happy to be a big part of this build, we did the cage in the car last year and now its back for all the fun stuff stay tuned for update pics on the build.. its going to be one badass RX7! #4rotor

13.01.2022 had this RB26 powered S14 was in for a turbo back 4" stainless exhaust with a magnaflow muffler, and also a baffeled catch can

13.01.2022 another cams national spec rollcage completed on this R34 4 door, for any cage enquires shoot us a message

13.01.2022 had jacksons s14 in to move the intercooler further back and did some new intercooler piping and intake pipe

11.01.2022 GTIR we just finished up this week, custom exhaust manifold for forward facing turbo, custom intake manifold, custom intercooler, custom radiator, 3.5" stainless dump pipe into a full stainless 3" exhaust, alloy intercooler piping, 3 in 1 custom tank (catch can, power steer res and radiator overflow), alloy radiator hard pipes, mount oil cooler, alloy fan shroud, mount fuel cell, and few other small things

11.01.2022 Mitchs 4g63 Datsun 1200 wagon we have been building for a while. Full house nitto 2.2 with a powerglide behind it, custom everything... its gunna be a badass streeter

11.01.2022 Twin shooter Tuesday

11.01.2022 GC8 in for custom twist mount turbo setup, custom up-pipe, full stainless 3.5" turbo back exhaust with a magnaflow muffler and stainless 100 cell cat, plumb the wastegate in, weld alloy bend on comp housing and join into existing pipeing, intake pipe and plumb bov into intake pipe Diversion Garage

11.01.2022 R32GOD gtr in for a chromoly rollcage and removable parachute setup. Retaining the full interior and use of back seats with removable intrusions

10.01.2022 due to the developing issue with COVID-19 our workshop will be shut to the public and we will be operating by appointment only during this period. Thanks,

10.01.2022 little mazda mx6 in for a weld in 4 point cage

10.01.2022 Nathans colorado we did a weld in rollcage with removable intrusions, fitted a pair of velo race seats and a pair of velo harnesses

09.01.2022 had marcos R34 in for a 4" stainless turbo back exhaust with a magnaflow muffler

09.01.2022 We had this tuff GT4 celica in from Capalaba Motor Repairs for a chomoly 6 point rollcage and removable parachute setup

09.01.2022 This little R100 we just finished up on. custom tube subframe/tube engine plate/gearbox mount, custom radiator/oil cooler/fan shroud, fuel system, full stainless exhaust system, catch can/rad overflow, trans tunnel hole repair, custom shifter stick to replicate stock one with factory gearknob , mounting of electrical hardware, water pump hidden under guard and a heap of other stuff

08.01.2022 forward facing fridays

08.01.2022 just finished up on a this supra with a funny car rollcage, removable parachute setup, mount kirky seats, tailshaft loop and a front tow hook

08.01.2022 another subi in for a twist mount using a gtx35 gen2. custom up pipe, single 3.5" stainless exhaust system to twin 3" at the rear with a pair of magnaflow mufflers, screamer pipe, intake pipe and join intercooler piping into existing pipework Diversion Garage

08.01.2022 A Beautiful group 3 Brock VK commodore that was in for a stainless exhaust and a couple other small things

07.01.2022 kierans R34 was in for a 4" stainless exhaust, magnaflow muffler, intercooler piping, 2 in 1 tank (catch can and radiator overflow), mod the gearbox crossmember to suit a jatco and alloy cover plate for drivers inner guard

07.01.2022 guys over at next up making some good power on tuans GSR we did all the fab on last year. auto and awd this thing will be a little weapon

07.01.2022 Thanks to everyone for another outstanding year. Couple of cars to reveal in the new year we have had under wraps . Stay safe over the holidays and see everyone in 2020!

06.01.2022 R33 GTR race car we just did a CAMS national spec rollcage, body mounted wing mounts, catch can, mount mirrors and few other minor things

06.01.2022 Little peak at something we have been working on for the guys at Diversion Garage

05.01.2022 101 motorsport 20B RX7 back for a new exhaust manifold, alloy dimple die interior floor panels, alloy radiator cooling panel, radiator swirl pot, modify dump pipe and cooler pipe to suit new turbo location.. sorry about the lack of posts been super busy and apologise if we have been abit slow to respond to messages

05.01.2022 6.79@212!!!! We are proud to be apart of this awesome team and car

04.01.2022 E92 M3 we had in for a bolt in half cage

04.01.2022 Been abit slack on uploading stuff we have been super busy. Heres a R34 GTR NUR spec with a 2.8 stroker we had the pleasure of doing the hotside fab on, we made a big runner manifold for it, pair of turbosmart 40mm wastegates, borgwarner EFR 8474, 4" stainless dump pipe, both wastegate pipes plumbed into the exhaust and modified the turbo outlet to join the existing pipework

04.01.2022 wasent an ideal jambo for us due to haveing some teething issues Wednesday night testing and putting us out for the weekend, but still managed to break into the 8s with an early shutoff and PB in the mph on the previous pass. time to get the 60ft down and go deeper into the 8s #streetcar

04.01.2022 we finished up on the sil80 build, from the dyno friday night straight to the track to get some licensing passes in, managed to trap 151mph still on a quite low boost setting, will finish licencing this week and do some testing before jambo

04.01.2022 Deans badass S14 all finished up and ready for the dyno

03.01.2022 parachute finished up, fully removable

03.01.2022 Finished up on a whole new hot side on daves supra. Precision 7675 with a turbosmart wastegate, custom exhaust manifold, 4" stainless dump pipe, hidden screamer pipe, new hot side intercooler pipe with quick realease clamps, final fit, plumb the turbo up, and a whole heap of other small things

03.01.2022 had robbies STI in, we swapped out the precision turbo for a GEN2 Garrett, removed the headers and fitted EGTs, wrapped the headers in titanium heat wrap, modified the up pipe to suit the new turbo, fabricated a new 3.5" stainless dump pipe, modified the screamer pipe, joined the front housing up to the existing intercooler piping and fabricated a new baffeled catch can

03.01.2022 We had nicoles ute in for a a weld in cage, fit a pair of kirky seats, fit simpson harness and mount a couple other small things

02.01.2022 Weld in half cage for a DC5... sorry for the lack of posts we have been suuuuper busy and have a couple of big projects on the go we will put pics up of when they are finished

02.01.2022 We got an instagram page now, for some more reguar updates click the link below and hit follow https://instagram.com/fablabqld?igshid=a64wubgmtow

02.01.2022 The guys at diversion garage getting it done with 550awhp from a gtx3076 on an evo 5 we had the pleasure of doing a heap of stuff on not so long ago

01.01.2022 we had this evo in for a forward facing setup, we did custom exhaust manifold, 3.5" stainless dump and exhaust system, 2 different screamer pipes (1 hood exit and 1 ground exit), custom intercooler pipes, mounted the radiator and air-con condensor, mounted and oil cooler, 3 in 1 custom tank (catch can, rad overflow, windscreen washer bottle), unpicked some un-nessasery brackets in the engine bay. the car still retains aircon, fit a decent size dump pipe, fit a big runner manifold, enough room to run an air filter if desired and easy to work on. back to the boys at Diversion Garage to finish it