Handy Machining in Mount Evelyn, Victoria, Australia | Local service

Handy Machining

Locality: Mount Evelyn, Victoria, Australia

Phone: +61 428 371 001

Address: 6 Clancy’s Rd Mt Evelyn Vic 3796 Mount Evelyn, VIC, Australia

Website:

Likes: 201

Add/Update information

Reviews

Tags

• Local service

25.01.2022 Custom made tool for local Kenworth dealer they asked me to make up a tool to hold a dial indicator so they can measure cylinder block to cylinder liner height

25.01.2022 A bunch of special order bolts made up for a drag car that’s under construction

25.01.2022 Steering components made up to clients specs for a drag car that’s under construction

24.01.2022 Something new for something old A new wheel hub puller for a 1927 - 29 Chev the old one gave out after 90 years of service

24.01.2022 A run of small parts made up for a valued engineering company made from stainless and brass

23.01.2022 Parts made up for a client that needs a 45 degree base on his router made from stainless and aluminium

23.01.2022 Finally after nearly 40 years of pissing around with tins of petrol and cans of degreaser this lands today

20.01.2022 V6 Commodore heads resurfaced for a local young fella today

20.01.2022 Did a run of 20 of each size of bronze bushing needed for Scania bus engine oil centrifuge Bus company can get their bus back to work now

19.01.2022 Just a couple of the many parts I’m making up to replace damaged or worn parts in a mustard grinding machine Hungry Jacks might be short on mustard sauce till this baby’s back together Thread on the shaft is 39 x 1mm pitch

19.01.2022 Another batch of fittings machined up for clients in the heavy towing industry

18.01.2022 Then and now photos of a small surface grinder that came to me a while back its had a good clean up a bit of tweaking here and there and a coat of paint

18.01.2022 New water pump impeller for a 1927 Chevrolet truck In the process of a water pump rebuild Cast up the brass from old brass fittings I had and then machined it to match the original

17.01.2022 Bit of a rework on a boat rudder today mill off the original weld and adjust rudder angle to clients specs then reweld and refinish

17.01.2022 Spike for hydraulic punch I’m making at work for punching holes in old LPG Tanks made from 4140 steel

16.01.2022 2 water pumps rebuilt for 1929 & 1927 Chev Made up new impellers and shafts Machined housings out to accept needle roller bearings and modern seals to replace the original brass bushes and asbestos compression seals Should last another 90 years now

15.01.2022 Fire box vents cut into stainless steel door for an outdoor pizza oven Wooden handle is a touch agricultural but will do the job required

14.01.2022 Made up a set of axles for a robotic drain camera out of 316 stainless. Client can put it back to work now

10.01.2022 A bunch of retaining pins made up ready to go to a Towing company in northern suburbs

09.01.2022 This is all the bits and pieces made up or repaired and modified And a pic of them all assembled into the machine housing ready for delivery Been a great sublet job to get done and finished

09.01.2022 A little bit of art work done this week

06.01.2022 Another job done ready to go Keyways cut into wheels, sprocket and stainless steel shaft

04.01.2022 Just replaced Turbo on wife’s Hyundiah Veloster. OMG & again OMG unles you are blessed with fairy sized fingers and wrists that bend backwards like universal joints run and hide if someone asks you to do one for them Unfortunately I been blessed with fingers like fence posts and that makes micro surgery a challenge. But hey jobs done

02.01.2022 New bandsaw all set up in the workshop and it works a treat

02.01.2022 Couple of small jobs done & dusted today so clients can get on with their jobs this week