Kurt March in Devonport, Tasmania | Motor vehicle company

Kurt March

Locality: Devonport, Tasmania

Address: Devonport 7310 Devonport, TAS, Australia

Website:

Likes: 173

Add/Update information

Reviews

Tags

• Automotive, aircraft & boat
• Automotive repair centre
• Tyre dealer & repair shop
• Motor vehicle company

25.01.2022 Had a broken bellcrank in a 25T Clark forklift today, removed steer axle and is off being repaired and strengthened, refit next week

25.01.2022 Re-conditioning a YD25 diesel out if a D40 Nissan Navara also Re-conditioning a small block Chev 350

24.01.2022 https://www.facebook.com/583325402060784/posts/1185323538527631/

22.01.2022 I always jack up the steer axle when servicing trucks to grease and check. The RH bearing had only slight movement but could hear it so I got him to get a set. Today fitted a new set to both sides, would have been a costly failure on roadside otherwise

20.01.2022 Finished a major mast overhaul for premium fresh, reconditioned lift cylinder by Southcott, major cracked repairs by wooton and Byrne, roller repairs, re-bush and machining done by me. All disassembly and assembly done by me

20.01.2022 Rebuild time for this Toyota Forklift, one from a fleet which I maintain.

19.01.2022 Sourced all the parts, also had hoses made to suit for this TCM sideshift install. Push button on the tilt lever which changes it to sideshift via a diverter valve, simple and effective.

19.01.2022 Weld repair on a flat spotted container forklift mast roller, then machined with a 5 degree taper on each end so that bearing load is in the middle and even on bushes

19.01.2022 3208 turbo CAT engine out of one of K&D Sims coaches, assembling it after it has been fully reconditioned

19.01.2022 D40 navara EGR cross over tube, they crack off and cost a heap to replace. I have previously welded a couple with a solid plug with good success, this time tubed it. If for some reason the weld cracks on the thin tube the way the pipe bolts in it is impossible for it to slide off tube insert and being a tight fit won't leak. Cost effective fix that keeps customers happy

18.01.2022 So I do enjoy getting up to my elbows in black detroit 2 stroke engine oil, the Jake brakes were a bit average on a 6V92T in a mates bus, all fixed now after a few checks and replacing the seals in the Jake housing connecting gallery seals, and it working well - at least 50% better

18.01.2022 I do all repairs and maintenance to forklifts of all shapes and sizes. I have alot of experience with container forklifts from new to very old. Hyster, Clark, Valmet, Omega, Lees etc

18.01.2022 Something different. Replaced the convertor/flywheel housing O ring as well as a service and checkover of this old International 507 with a Komatsu 4cyl diesel

18.01.2022 Service manual clearly states to change the air con filter at services or at a minimum check it, this Kluger has been serviced at a local workshop in the past. Sometimes you don't get what you pay for..

18.01.2022 Nothing is ever simple. Here for coolant leaks. Had trouble getting the cab up then found a cab mount bolt missing. Temporary fix will do for a while.

17.01.2022 Swapped out a damaged Eaton gearbox in this Freightliner, while in there replaced rear main seal, clutch, rear engine mounts and starter motor

16.01.2022 This Mitsubishi will be like new with a few new parts in the over complicated gear linkages.

15.01.2022 Reconditioned hydraulic steer and tilt cylinders on a high hr Toyota forklift using seal kits. Prevents machine down time and extra expense not needed if cylinders were to be taken to a hydraulic shop

13.01.2022 Something different on Saturday, full set of brake pads and rotors on a cement tanker, quite a job which took the day to complete

13.01.2022 Machined a Mitsubishi truck flywheel today for John at Wiggies, can do flywheel machining after hrs to speed up equipment down time

12.01.2022 I do fleet servicing and preventative maintenance. This company is one that I have worked with for over around 4 years

11.01.2022 This is a 3CD1 Isuzu engine from a TL brand pivot irrigator that I fully reconditioned, tested prior to fitting

11.01.2022 Pulled apart a 25 tonne Clark today, repairs to be done include lift cylinder re-condition by Southcott, crack repairs, roller/bearings replacement/re-condition etc

09.01.2022 Working for Track and Truck In Ulverstone, pulling apart a transmission out of a 966G loader, enjoying learning something new

08.01.2022 Fitting a seal kit to this Lucas CAV distributor type injection pump. They are a very simple and reliable pump with the ability to reseal without effecting the fuel metering

08.01.2022 I replaced the rear brake rotors, brake pads and hub seals on this 2008 transit van, saved the customer $350 over the quote he received when dealership serviced

08.01.2022 New addition to my business. Will be continuing my mechanical work as well as keeping the family tradition going. Will subby with my recently purchased Kenworth, also will cart loads for customers using my newly purchased 45ft flat top complete with 3 way twist locks. Hope it works out

07.01.2022 A customers truck started pressurising cooling system and blowing coolant out eventually started missing, hard to start and lacking power. After fault finding it was found that n.o 4 injector was loose with damaged seals and injector seat was stuffed. Head was removed and seats were replaced then refitted along with a top end tune up. Problem fixed

07.01.2022 Haven't updated for a while , i enjoy a change and contact/casual fill in/drive trucks to keep busy

06.01.2022 Truck service and tune today

05.01.2022 Also do cars, changed the clutch in this Kia Rio, was quite good to work on once supported on blocks

04.01.2022 4Y Toyota engine, forklift spec (timing cover different with hydraulic pump drive) Was dusted and using oil, fully reconditioned with new head ready for fitting at Premium Fresh

04.01.2022 Reconditioned a Horton fan hub for Minecrete, failed yesterday, he sourced parts and is fixed ready for work Monday

02.01.2022 Reconditioned YD25-ddti ready to be fitted to a D40 Navara

01.01.2022 Replaced the clutch in this Isuzu Ridgid, machined the flywheel on my lathe, along with a service drives like new

01.01.2022 I've been run off my feet for a long time now and would like to apologise to customers who I still haven't completed invoices for from end of last month, you will still have 30 days from when I send the invoice. I don't expect a rushed payment especially the way things are ATM. Thanks