Pure FAB in Sydney, Australia | Vehicle customisation shop

Pure FAB

Locality: Sydney, Australia

Add/Update information

Reviews

Tags

• Automotive, aircraft & boat
• Vehicle customisation shop

25.01.2022 Another evo 7-9 hypex 347 stainless stock frame manifold out the door, with good peno you end up with a nice seamless transition between header/runners. Decked flat ready for install #suli_purefab #PrecisionFabrication #evo

25.01.2022 Little Mx5 we built finally hit the rollers for its run-in tune. Featuring a built motor all done in-house, extensive head work/porting and cam profile resulting in a very efficient setup, could have easily pushed it further on 98 pump but should be plenty for now till the owner gets used to it. Will be back for a full e85 flex tune, another 1000rpm plus another 10psi. All PureFAB turbo fabrication, off the shelf 347 turbo manifold, custom cooler and charge pipes. Tuned by Micks Motorsport

23.01.2022 Putting the new @everlastweldersaus torch to use with this custom radiator for the AWD civic. @pwrperformanceproducts core with sheet metal end tanks and AN fittings. Next up mounting and custom shroud/spal fan setup #suli_purefab #PrecisionFabrication #weldporn #Alloyfab

22.01.2022 Another podium finish at the flying500 for this red rocket built by Micks Motorsport, PureFab 347ss turbo manifold on board, super impressive 281kms from a 4banger

22.01.2022 Tims little RB30 ke30 corolla certainly lives up to its plates, car was transported up from canberra to get the PureFAB treatment. Alot of custom work including custom Sheet metal intercooler using a Hypertune 100mm core and billet clampsets, custom radiator setup with PWR Performance Products core billet clamp sets and swirl pot/header tank , catch can setup/overflow combo, custom 4" titanium dump pipe and side pipe small notch in firewall to accommodate, puke tank in boot, bosch motorsports DBW pedal install, shorty charge pipes, Nitrous tank install, custom 5" intake with seamless flange setup on turbo. Will be one to look out for when it hits the track #suli_purefab #PureFAB #PrecisionFabrication

21.01.2022 Custom sheet metal cooler fabbed up for the RB30 KE Corolla, used the largest 100mm core possible without hacking off the front grille entirely, nice and snug with shorty charge pipes #suli_purefab #PureFAB #PrecisionFabrication #ke30corolla #rb30det

21.01.2022 Another big boy honda setup, 7675 pte mated to our 347 ss hypex turbo manifold. These manifolds are becoming very popular with the RHD Honda platform in Aus as turbo sits square to block and gives good clearance for large frame turbo and big dump pipe. #suli_purefab #PrecisionFabrication #honda #k20 #b2r

21.01.2022 Baby Godzilla GTIR dropped in for a custom turbo setup/exhaust/charge pipes and intake. Custom 347 Stainless steel manifold with custom collector fabbed up to accommodate a T3 twin scroll setup. 3.5" stainless dump pipe, plumb back gate and electronic exhaust cutout with priority placement ( straight off the dump). Optional flange block off if they want to remove the valve and easy to replace. Vibrant flex pipes and all factory mounting points used. Modified cooler with HDI clamps supplied by customer #suli_purefab #PrecisionFabrication #GTIR

21.01.2022 Cranking out some 347 hypex manifolds. SR20 top mount, Custom F20C and couple of tubular 4G63 Stock frame replacements. What's your pick? #suli_purefab #PureFAB #PrecisionFabrication

20.01.2022 Another heavy hitting ek Honda setup for street / strip / roll race. This is 1 of 2 eks copping a 4wd conversion, alot of custom work. All turbo fab, custom fuel cell setup with extensive baffling and dual protec cobra pumps with holley hydramats will ensure over 1000hp supply without the need to run a surge tank and low current draw as they run brushless motors. Titanium cat-back, car will come back for a custom radiator and finish off loose ends before it gets wired. Will be a car to watch out for

20.01.2022 Some ally flange welds from today. Top 2 come off the intercooler, bottom is a 2.5" to 3" donut reducer to come off a turbo comp cover #suli_purefab #PureFAB #PrecisionFabrication #Alloyfab

20.01.2022 Getting through some charge pipes for another big boy K-series Honda setup #suli_purefab #precisionfabrication #k20 #alloyfab #weldporn #everlastweldersaus

19.01.2022 Had the pleasure of building the custom Titanium exhaust on the Evolution Racing Spares time attack evo. Super light weight and precision welded with good penetration for weld strength. #suli_purefab #PureFAB #PrecisionFabrication #timeattack #noshortcuts

18.01.2022 Evo X stock frame replacement tubular manifold. Also available for evo 7-9 Using hypertune 347SS components #suli_purefab #PrecisionFabrication #evox

18.01.2022 Badass AWD K powered civic all finished up, custom full length radiator tucked to accommodate the billet Gato manifold, gato to DBW flange adapter welded up, custom shorty charge pipes with billet Hypertune clampsets, overflow bottle, 5" intake pipe, additional engine mount tied into front traction bar to keep the motor from flexing, valve cover mod with an fittings and OEM breather welded and smoothed. Really looking forward seeing this car run #suli_purefab #PrecisionFabrication #awdhonda #kseriesonly #honda #k20

18.01.2022 Another EVO 4-9 Stock Frame Hypex 347SS tubular manifold out the door. Full back purge, seamless port work and decked flat #suli_purefab #PureFAB #PrecisionFabrication #weldporn #4g63

18.01.2022 Custom 4" Titanium dump and side pipe for drag racing duties finished up for the RB30 Corolla, full back purge, alot of heat with good penetration, mild hand polish on all pipes before weld up to get it looking nice and consistent will look amazing once its has some heat cycling. All reseviors fabbed up, charge pipes, dbw pedal mount, nitrous mount, puke tank which ill post in a new post. All thats left is a custom radiator setup to keep it cool and shes ready for pickup #suli_purefab #PureFAB #PrecisionFabrication #noshortcuts #weldporn #fabricationlife #oldschool #rb30 #titanium

17.01.2022 Took a couple of goes to dial in the 5" donut on the rotator to find the sweet spot, happy with the end result #suli_purefab #PureFAB #PrecisionFabrication #tig #aluminumwelding

17.01.2022 Custom Ti race slip on for a BMW 1000 RR. What a difference over the oem system. Burnt blue to suit the blue features of the BMW blue on bike #suli_purefab #PureFAB #PrecisionFabrication #bmw1000rr

16.01.2022 Honda catch can fabbed up, dual baffle setup with k&n panel filter. Nice little tie down/dress plate thanks to @milzymilz aka Milan engineering

16.01.2022 Ali dropped off his immaculate Toyota wagon. We did the turbo fab on this car about 6 years ago, its the first time I'm seeing it running in the flesh since the build started and all I can say is wow, what a wild ride. We installed a 3.5"' titanium flex and went over the car as Ali has a Toyota car event he wanted to get to. Should turn some heads #toyotafest

16.01.2022 Last job for the year, Evo in for Custom charge pipes with billet clampsets, Titanium intake pipe with billet clampset, titanium tip for the existing SMB muffler, Custom 3.5" dump pipe and plumb back screamer, modified shroud to suit oem radiator #suli_purefab #PureFAB #PrecisionFabrication #evo9

15.01.2022 Alis immaculate SR20VET powered datsun 1600 coupe was dropped off for some PureFAB treatment consisting of- custom hypex 347 stainless manifold mated to a GTX3584RS, custom intercooler setup with shorty pipes and billet hypertune clamp sets, Revised the existing radiator setup as filler was interfering with plenum so we built a remote header tank/Swirl pot setup, overflow tank, modified turbo comp cover for Wiggins ferrules, Alu to Titanium wiggins flange combo for the tita...nium intake pipe, titanium dump pipe with plumb back setup and full exhaust system with exhaust cut out, custom mounts throughout, custom catch can, mounted fuel cell with 4 point chromoly mount in boot with underside mounting plates/captive nuts and also tied in the sheet metal cover which makes trimming the boot a lot easier #suli_purefab #PureFAB #PrecisionFabrication #datsun #sr20 #titanium

15.01.2022 S14 dropped in for a vband 347 stainless turbo manifold to suit his MMP turbo. Manifold will suit all GT30/35R frame turbos. 50mm gen v wastegate retrofitted to hypertune collector, ample clearance everywhere for all the oem gear. Turbo inlet flange was machined down for a seamless transition after welding

15.01.2022 Titanium Tuesday, custom 4" Ti exhaust being fabbed up, more pics to follow #suli_purefab #PrecisionFabrication #titanium

14.01.2022 "BAGDAD" Spec Evo manifold heading to Mick Baghdadi of @micks_motorsport for another heavy hitter evo in the build. Same manifold currently on the red beast which is the quickest full trim street Evo in Australia on radials. Constructed from hypex 347ss which has proven to be extremely durable and lighter than your off the shelf steam pipe. Welded using the Everlast 210ext #suli_purefab #PureFAB #PrecisionFabrication #noshortcuts #weldporn #fabricationlife #micksmotorsport #everlastwelders #210ext #4g63 #bigturbo

14.01.2022 Michaels Immaculate Blown LJ Torana was dropped off for a complete cooling system - custom large core PWR radiator with sheet metal tanks, twin pass setup with large motor SPAL fan, custom header tank/ lower rad hose with billet hypertune clamp sets, Baffled catch cans, overflow tank incorporated into radiator, and a pedal modification to suit the new setup. Another very tuff streetcar to keep an eye out for at upcoming events #suli_purefab #PureFAB #PrecisionFabrication #LJ #oldschoolmuscle

13.01.2022 Mx5 all fabbed up with custom I sheet metal intercooler utilising a Hypertune core, our off the shelf 347 stainless side mount turbo manifold mated to a G25-660, next stop will be Micks Motorsport for a run in tune, setup will be good for over 400hp + atw

13.01.2022 Another Holden Gemini turbo manifold done, this time in Vband inlet. Ample room for wastegate and dump pipe, 347ss construction full back purge. Heading to @micks_motorsport to be bolted onto one of their built engines. These are becoming a popular option available in Vband/T2/T3. If interested contact @micks_motorsport as i believe they are putting together a group buy for these #suli_purefab #PureFAB #PrecisionFabrication #noshortcuts #weldporn #holdengemini

12.01.2022 Custom fuel cell for the AWD ek civic, extensive baffling and holley dynamat plumbed to each pump with filler welded internally for cleaner look. Twin protec cobra brushless pumps. This setup negates the need for a surge tank everythings incorporated. Low amp draw pumps controlled via pwm output via ecu makes for a very efficient setup capable of big HP #suli_purefab #PrecisionFabrication #protecfuelpumps #holleyperformance

12.01.2022 Big congrats to Team ERS . We did some last minute fab work before the event including new cooler setup/pipes/clampsets and modification of the titanium front pipe that we previously fabbed up to suit the new subframe setup in car #1

11.01.2022 Some close ups on the weld detail #suli_purefab #PureFAB #PrecisionFabrication #tigwelding

11.01.2022 Haven't posted in a while as we've been flat out. Tim's little RB30 corolla was dropped off for its final bits of fab work. We fabbed up a custom dual protec cobra pump fuel cell with billet mounting plates, extensive baffilng, holley hydramats with speedflow plumbing. PWM controlled, low amp draw and enough fuel to make over 1000hp.

09.01.2022 Another one of our Honda k20/24 347 stainless T4 twin scroll turbo setups for a DC2 Integra. These are an off the shelf turbo manifold which are designed for RHD vehicles so no funky angle on the turbo which also leaves miles of room for a big dump pipe(can easily fit 4"). We fabbed up a 3.5" Turbo back system mated to a beautiful custom stainless muffler made by the boys at @performancexhaustcentre , Car in question made just shy of 600hp with a stock unopened motor #suli_purefab #PureFAB #PrecisionFabrication #hondaintegra #k20

09.01.2022 Promod style RB30/26 Turbo manifold setup with Titanium exhaust to suit G42 garret with the big comp cover. Places turbo up front away from strut and valve cover making it easy to work on and miles of room for a massive dump. The ti dump is 4" with long radius pie cuts and still heaps of clearance everywhere. This setup going on a @micks_motorsport built rb30/26

08.01.2022 Quickest and fastest 3/4 Chassis Sr20 on the planet Well done to Micks Motorsport and all involved. PureFAB custom turbo manifold on board.

08.01.2022 Custom back door cooler setup coming along nicely for a very tuff first gen Escort in the build. Hypertune core #suli_purefab #PureFAB #PrecisionFabrication

06.01.2022 Another quality honda setup done and dusted for the boys at @highend_automotive . Alot of hours and attention to detail poured into this car, Custom hypex 347 ss turbo manifold with 60mm external gate setup, custom sheet metal intercooler with shorty charge pipes, chromoly mounts top/bottom, cooling system with pwr core/sheet metal end tanks/custom shroud/spal fans/ header tank/swirl pot/ overflow, billet fuel rail and dbw setup including bosch dbw pedal install, Mercedes p/s pump installed under dash, emtron ecu mount 3.5" stainless exhaust with exhaust cutout, the list goes on #suli_purefab #PureFAB #PrecisionFabrication #noshortcuts #weldporn #highendautomotive #k24 #honda

06.01.2022 Monday morning coffee and donuts

06.01.2022 Custom BMW 1000rr Ti race slip on

04.01.2022 New Vband inlet turbo manifolds to suit gtx30/35 and the aeroflow range of gt30/35 for evo 7-9. Fits with oem radiator and thermo fan. Constructed from 347 hypex. One heading to micks motorsport which i will upload some pics fitted, another heading to Bill #suli_purefab #PureFAB #PrecisionFabrication #4g63

04.01.2022 Couple of turbo manifolds ready to send out for 2021. Another honda T4 twin scroll for a 4wd big turbo setup and one of our evo 7-9 tubular manifolds to suit the mid frame gtx30/35 and 45mm gate, a very popular street combo. 2021 will see some very fast Honda's in Aus

04.01.2022 Just a little G42 setup on an SR20 datsun wagon, custom T4 T/S hypex 347ss turbo manifold with egts, modified existing radiator - notched to make room for the 3.5" hotside pipe with billet clamps, changed inlet/custom header tank, modified existing intercooler, custom stainless dump pipe with aes cutout + screamers

03.01.2022 Youve seen the seamless intake mod when using a billet clampset here is a seamless outlet mod using a billet clampset on a new intense turbo for a time attack car. No etching or welds visible for a nice clean OEM look #suli_purefab #PrecisionFabrication

03.01.2022 Quick shout out to the boys at @performancexhaustcentre for supplying us with a custom single in/dual out muffler for an immaculate S15 we just finished. Decided not to lobster and just go for a clean look with dual 3.5" tips, turned out much nicer than expected on the car. These mufflers are hands down the best quality removing annoying drone and also look the part more pics to follow

02.01.2022 Hotside charge pipe for a very tuff RB30 powered KE30 Corolla, all pipes are getting clear coated so pipes get heavily scotch brited and welding on point with a nice even etching around the entire weld will look mint when coated #suli_purefab #PureFAB #PrecisionFabrication #ke30 #alloyfab #weldporn #rb30

02.01.2022 Mazda BP 347 stainless Turbo manifold shipped out to the UK. Provisions for EGTs to suit a new garrett G25 turbo #mazda #mx5 #miata

01.01.2022 Big congrats to the boys from ERS, we did some last minute fab work on the car for this event, new charge pipes, modified the intake manifold to accept smaller dbw throttle, mounted accusump, welded sway bar mounts to subframe.. The car also runs one of our custom titanium dump/front pipes

01.01.2022 VL turbo dropped in for some turbo Fab, custom dump pipe, charge pipes with billet clampsets, mount gate/screamer, custom shroud to suit 16" Spal fan #PureFAB #PrecisionFabrication