SA Performance Centre in Adelaide, South Australia | Vehicle customisation shop

Click/Tap
to load big map

SA Performance Centre

Locality: Adelaide, South Australia

Phone: +61 417 801 480

Address: 14-18 Dundee avenue Holden Hill 5088 Adelaide, SA, Australia

Website: http://www.bulletraceengineering.com

Likes: 606

Reviews

Tags

Click/Tap
to load big map

25.01.2022 Three little billet blocks... One 2J One RB One 4G All waiting for the big bad wolf to blow their house down....(Thats Me)... All to be built this week with BME alloy rods & BME pistons. See more

24.01.2022 Custom fitting made to fit back of RB head for dry deck set up.

24.01.2022 Just some pictures for whats will be on the street in 2019 !

23.01.2022 6.97sec @ 202mph JUN II FIRST, FASTEST, QUICKEST AND THE BEST STREET REGISTERED NISSAN SKYLINE GTR R32 IN THE WORLD!!!!!!!!!!!!

23.01.2022 VP Race fuels. Lots in stock. All the popular types.

22.01.2022 Some SR heads getting the Clover Cheif Chamber upgrade and dry deck mods with oversized inserts. BIG boost set up!

21.01.2022 Still building,full race-Trimatics-Powerglides-C Series Transmissions,Agent for Gear/Vendor Hi-Performance Under/Overdrive units,and the Supa-Tuff 9" Centres, call for quote on 08 82661688

20.01.2022 Made some special guides with built in spring seat for a particular head. Job cane out real nice!!

20.01.2022 Lets flow this sucker heads and intake.

20.01.2022 Isoptropic polishing in action Weve been doing....... Cranks Conrods Camshafts... Diff gears Gearbox gears Valve springs Retainers And more.! See more

20.01.2022 Some CNC ported LS3 ports.

19.01.2022 Looking at an RB26 head on a billet RB30 from down below.

19.01.2022 4V heads by 3 pairs all getting tongues just fitted.

18.01.2022 Heres a combo billet RB block with BME rods and pistons in stock ready to go.!

18.01.2022 2JZ CNC ported head.

17.01.2022 Some BME goodness.....alloy rod with a serious boost piston.

17.01.2022 SR20 billet block 800+HP streeter nearly ready for some RPM.

17.01.2022 Bullet Race Engineering billet block display at the new Tailem Bend Motorsport Park for the World Time Attack Challenge.

16.01.2022 Lots of LS heads to be CNC ported this week. Cathedral and rectangular heads in stock ready for change over.

15.01.2022 Some chamber mods..... before and after

15.01.2022 2000hp RB 30/26 out the door. BME alloy rods and pistons. Fire Ring head gasket set up. Kinsler 3000 HP mechanical fuel pump. 75+ PSI boost.

13.01.2022 Tims Holden finally produced at AIR 355 Holden with factory cast iron heads. 3000lbs. T350. Dominator convertor. Zagari rear clip. Some upgrades and patience paid off. She getting fast now.... 9.24ET @ 142 MPH See more

13.01.2022 Small Block Chev 610 HP ULP 98 Street cruiser

13.01.2022 Here are some cranks and rods done in the last few weeks. Isoptropic polishing for that extra mile.!

12.01.2022 RB26 CNC ported head with a CNC billet Intake.

10.01.2022 CNC Chambers and seats cut on the Newen for the best results.

09.01.2022 Cats out of the bag!! 6.97@202 using a Bullet Billet block which we have been refining since just after GTR Festival 2018! Power has never been an issue for quite sometime now... Bullet Race Engineering was right after all.......... #castaintfast

08.01.2022 Billet 2J block at work!

04.01.2022 Here is a billet RB30 build with BME alloy rods for a circuit race deal. Spool crank. BME pistons. Billet CPC Intake.

02.01.2022 RB30 Blower bracket and billet rollers installed and ready for action. Just waiting for blower belt, fittings and some bolt on bits.

02.01.2022 Engine dyno run on a Billet block RB26 Twin turbo 1100+ HP 600 + ft/lbs

02.01.2022 Small block mopar looks so much better with a billet timing cover. 408 cube, Indy heads, 650hp all day cruiser.

SA Performance Centre in Adelaide, South Australia | Vehicle customisation shop