TTT Performance in Dandenong, Victoria | Automotive, aircraft & boat

TTT Performance

Locality: Dandenong, Victoria

Phone: +61 437 744 573

Address: 1 Station st 3805 Dandenong, VIC, Australia

Website: http://www.hotsixes.com/ttt-performance-engineering

Likes: 1107

Add/Update information

Reviews

Tags

• Automotive, aircraft & boat
• Automotive manufacturer
• Vehicle customisation shop

24.01.2022 Holy mother of god !!! Watch the gauges in this drag car, in 5 sec, it pulls 500khp and 6gs and a tank of fuel Simply incredible!

21.01.2022 STOLEN. PLEASE SHARE and Keep an eye out, we have had 7 superchargers and 1 x 250 Blower Shop Big Block Chevy black intake manifold and drive kit stolen, They w...ere more than likely stolen from Mont Clair California or Possibly but unlikely From Spotswood in Victoria during unloading. As we had taken delivery of these they are not covered by insurance and it is a huge loss to absorb. Pictured are the location and stamping of the serial number on the intake side of the blowers. Also listed below are the serial numbers. We know the chances of them being recovered are very slim. If you have purchased one of these blowers with the serial number below please contact us, all we want is the details of who and where you brought them from so they can be dealt with. 9945-6v Polished billet 6V/71 10155-6v Polished billet 6V/71 10174-6v Polished billet 6V/71 10130-192 Black 192 RARE WAS A SPECIAL ORDER 10131-192 Black 192 RARE WAS A SPECIAL ORDER 10171-192 Polished 192 Billet 10173-192 Polished 192 Billet See more

20.01.2022 THEY'RE BACK. TTT press on pulley kits are available again. We've made a couple of changes, the O D is now 85mm for a bit more boost 10PSI+ and the cross section is thicker to make sure they can be pressed on and off multiple times and still run true. http://www.ebay.com.au//Commodore-VS-VT-VX-V/162638437993

18.01.2022 Nicks VY2 L67 in for a full de mod and revert back to a standard freshened up engine after having been a BTS R&D car for the last 5 or so years. Sad to see her... up for sale as it's the cleanest VY2 Calais we've seen. Fully standard L67 with a TTT Performance 85mm press on pulley and dyno tune. 150rwkw/ 900Nm @ 10.5psi

17.01.2022 Check out our ebay store http://stores.ebay.com.au/TTTperformance-ph-0437744573

17.01.2022 Valve Spring Dynamics Movie - The Enterprise Edition of Engine Analyzer Pro lets you enter details about the valve spring(s) you are using. It will actually im...port files from the Spring Wiz discussed in Item 1. It will then run the spring(s) in the Engine Analyzer Pro's valve train dynamics model and see what the springs are doing, if they are going into resonance, allowing the valve train to go out of control, etc. The Enterprise Pro's calculations are much more detailed than the simple Spring Wiz. And it does not say if a particular combination is good or bad. It just shows you what is happening and then you must decide if you want to use it. Please follow this link for further information about the Engine Analyzer v.3.9 Pro in The Enterprise Edition; http://performancetrends.com/Engine-Analyzer-Pro-Enterprise A long time customer of ours sent us a high speed movie of a valve spring pack in operation at high RPM. Here you can see the coils oscillating and the outer spring actually breaks during the movie. It really gives you an appreciation that things are not always under control, even in the most well built race engines. Please watch movie showing actual valve spring dynamics (and spring actually breaks) You need the Enterprise Edition to be able to simulate valve spring dynamics, which is a $250 add on to the Engine Analyzer Pro v3.9 B. Many customers likely own the Engine Analyzer Pro v3.9 A. If so, the 3.9 B update is $95 (with many new features, engines, etc) and the Enterprise is another $250, for $345. However, we do a package update/upgrade for $300, a $45 discount. To email us about updating or upgrading [email protected] or call 248-473-9230.

12.01.2022 The TTT Ute is back. LS1 out L67 in. Very happy with the mafless tune from Boost and Tune Solutions Still messing with a few things to make it drive the way I want, then will start testing some new products.

08.01.2022 You can FEEL that nitro power in super slo-mo! #NHRA