Ultimate metalworks in South Windsor | Car service

Ultimate metalworks

Locality: South Windsor

Phone: +61 447 890 529

Address: 5/3 white place 2753 South Windsor, NSW, Australia

Website:

Likes: 7283

Add/Update information

Reviews

Tags

• Commercial and industrial
• Car service
• Metal fabricator

25.01.2022 Tough! On billets One of our smoothest engine bays UMW LS T400 conversion kit 9 ... Billet axles Coilovers Tube arms Full rewire Haltech computer system Wilwood brakes all round Underdash pedal assembly Attention to detail in this car is 2nd to none! @markbrandonread killed it with the assembly and fit up Now for Rego and cruisin’

24.01.2022 Our shop Vk has been sitting like this for a couple of years now.. Think its time to lay paint, get Warspeed Industries to finish the new 540cube combo and get it finished!

24.01.2022 Another set of boot panels and tubs but this time running stock floor and fuel tank..

23.01.2022 VL LE done Tubs for 275 radials But also running dished Momos #ultimate Vk #VL #commodores

23.01.2022 Coyote powered Capri on its last few things then off to be painted.. Rolling on Dummy wheels as it will get some 275 radials on welds.. #coyote #capri #tubbed #blown

23.01.2022 We are looking for the following: Experienced vehicle fabricator Apprentices Accessory fitter with basic mechanical and auto electrical knowledge... office receptionist/shop manager/social media Have heaps of work. Min. 40 hours a week. Paid good hourly rate. super etc Just need to turn up on time and do some work. And be organised and fussy Anyone with drive and motorvation to build some cool things in 4x4 and custom cars. Huge variety of work Must have licence...

23.01.2022 Is it even a blue VK if it’s not on @simmonsaustralia FR22s? Sent to the paint shop last week and coming back to fit the harrop blown LS using one of our UMW conversion kits

22.01.2022 LS2 blown VL streeter in for some mods.. Tubs Boot floor Recessed fuel cell 4 link... 9 Coil overs All the usual stuff to fit the Simmons See more

22.01.2022 Fr1s by Tempe Tyre & Wheel Centre

21.01.2022 ~~VB-VL~~ 1 of our UMW LS conversion kits ready to go.. We have ran these kits in multiple cats making great power NA and BLOWN These kits allow factory starter motor location with steering rack mods or relocating. Even power steering!... Perfect for dart blocks with no left hand starter option or anyone wanting 2 extractors or even just hate the other kits on the market.. Included in the kit is: 1 7/8 or 2 extractors in either stainless or mild steel with collectors UMW Engine mounts UMW Gearbox crossmember 25mm Billet Spacers (smallest on the market) Extended steer shaft $4500 DM to Pre order for a kit with a 2 week build time.

20.01.2022 ******SOLD SOLD SOLD****** Not many vks built to this quality! And its for sale! ... Immaculate inside and out. Built by a Very fussy owner Details in the last pic!

19.01.2022 3 steel reverse cowl welded and smoothed underneath then painted by @imperial_bodyworx

19.01.2022 One of our Smooth engine bays done a couple of months ago and then painted by @imperial_bodyworx We dont recommend any one else but @imperial_bodyworx when it comes to paintwork! Check out the dipped bronze everything! Pops with the blue and something different!

19.01.2022 Pro street is in! Chevelle now rolling on some big tyres.. #ultimate #ultimatemetalworks #prostreet #chevelle #tubbed #bigblock

18.01.2022 Quick prototype arm in the build.. To suit VB-VS Adjustable chromoly lower arms and will have matching chromoly caster arms! These will be perfect for anyone running 22s and just needing to pull the wheel in slightly to clear! Or running welds and they are sticking out a touch too far? ... Being length adjustable, the wheel alignment and camber can now be spot on Sold complete, powdercoated or raw, ready to bolt in! Will have 10 sets in stock in 2 weeks. Can preorder to secure them or wait until we have more on the shelf. 3 sets are already day sold. $1500 for the 4 arms. (If you add up reconditioned stock lower arms $400 or the parts and caster rods $650 then the labour to shorten and powdercoat them to have non adjustable arms that are heavier and ugly) These are worth having!

18.01.2022 One of our sheet metal rear ends.. Fully welded and welds ground.. Not because our welds are bad.. but because we love giving the job to the painter the best we can and it makes their job easier

18.01.2022 Quick engine bay clean up today and some chassis plating to suit the LSA. A lot of engineers are now asking for these plates to be welded on.. we will have stock in a week or so ... For us to weld on or DIY option See more

18.01.2022 Another one out the door today.. You wont find a VK straighter and sharper than this! Massive attention to detail in the prep and paint to get them lines perfect!... Engine bay UMW LS conversion kit with factory starter Haltech and full rewire Complete rear end inc 9, coilovers, 4 link etc Plumbed by @scott_b_2019 late last year

18.01.2022 A few early commodores were in the shop a month ago.. #vk #vl #specialist

17.01.2022 We are looking for another full time fabricator.. Must be proficient in sheet metal work, tig and mig welding and have the right attitude and eye for detail.. If you think you fit this or someone you know does, please send a DM or call the shop

17.01.2022 This VK is being built for a client in NZ.. off to blast and then @imperial_bodyworx for a spray then back to fit up the whole car, wiring, plumbing and the @warspeed_industries blown LS. This is a complete turn key package from supplying the car and all parts to tuning and testing the car before shipping it across the ditch This has the best of the best parts going on it and no expense spared.. Keep an eye out for the rest of the build..

17.01.2022 We were Running the ve ute on the dyno yesterday.. making over 700hp at the wheels for this stock bottom end is plenty.. With our newest team member very sufficient in automotive wiring, tuning and mechanical we have a few of the big builds on the go soon to be wired, plumbed and tuned by our team.. This allowing to control the quality and reassurance to the customer that its all covered to a high standard.... Thanks to @europrestige for the use of the dyno

17.01.2022 Simon mokdassi brought his VK in for a tickle before fitting his turbo LS and bringing it back for the dump etc Sheet metal boot floor, boot panels, tunnel, smoothed bay, kirkey race seats, coilover mounts Keen to see this one getting abused

16.01.2022 JJ has been pumping in the coyote powered capri.. Up next is hidden booster/master and mount a 6speed shifter, handbrake, fuel cell etc then strip down for paint!

16.01.2022 Is it even a LS if @warspeed_industries hasnt gave it a tickle? turbo LS VL in for engine mount kit running factory starter and factory power steering , plumbing fuel system and full wire and tune..

15.01.2022 Another one done Smoothed bay UMW LS mount kit Cooler piping Dump and exhaust... Full fit out including Holley terminator ECU Haltec ic7 dash Fuel system Trans cooler and remote oil filter UMW HSV brake adapter kit Drove in as a 308 Drives out @warspeed_industries powered LS iron block striker with all the goodies and a decent size turbo hanging off it.. See more

14.01.2022 Something different.. a VK that’s not blue Sitting tough on some @simmonsaustralia fr20s Tubbed, coilovers, tube arms and boot panels.. Diff housing, centre and axles supplied by SCW... Another 5 coming out by Christmas

14.01.2022 SV88 just about finished! This has every box on the commodore list we have to offer! All will be unveiled one day soon..

13.01.2022 Pretty tough HK in the build.. Came to us for some sheet metal floors, 1/4 mods, smooth firewall out and a couple of other things.. Big difference from when it came in as chassis rails, tube and tubs already in it. Plans are turbo LS and street duties on the 275 radials..... @gazzardbrothers rear end @raceproductsau diff and floaters

12.01.2022 Camaro rear end finished off 4 link strange chromoly housing braced Strange coilovers Mark Williams axles... Wilwood brakes Boot floor Custom Fuel cell and In tank pump setup.. another one out the door See more

12.01.2022 Thats a wrap for the Capri!

11.01.2022 WET333 came in for a rear end overhaul now it’s getting a @warspeed_industries big cube LS with a harrop on top! Sitting tough on the 20x11 @walkywheels widened by @aa__welding

11.01.2022 A quick freshen up on the rear end to get this Vl on some @simmonsaustralia flow formed 20x10s Drive in drive out tubs, coilovers, tube arms, shorten diff etc

10.01.2022 Kombi airbagged all round to help the wheelchair bound driver transfer from his chair to the seat Changing lives Using accuair endo tank and slam bags from @airide_suspension_supplies All digital self levelling Engineered

08.01.2022 Another engine bay on its way.. This one is for Simon, he is trying to keep this build tame compared to his other car.. XYKING But with talks of a GTX55 and DART block to power the tubbed and caged VK, I dont think it will stay tame for long

06.01.2022 Cool build we have going on at the moment.. HELL CHARGER Hellcat powered Dodge Charger With some big tubs for the billet wheels.. pro touring resto mod.... Aircon p steer etc See more

05.01.2022 First one out! finished this for @customwheelsandtyres Mint Xe falcon on some @simmonsaustralia fr20 flow formed 20x8.5s front and 20x10s rear Shortened diff New 28 spline axles and LSD centre with a custom top arm to suit... Sitting pretty nice for a family cruiser #simmons #ultimatemetalworks See more

05.01.2022 1 last Vk for the year.. Tubbed for the 22x11 Simmons All sheetmetal boot with boot panels Strange sheet metal housing Strange coil overs Strange 35 spline billet axles ... UMW 4 link and panhard rod UMW LS conversion HSV brakes all round Custom 100L fuel cell This is also running our UMW chromoly front arm kit to slam on 22s (not fitted in the pic) We will have 9 kits, LS conversions and front tube arms on the shelf early feb Merry Christmas from the team and we will be back January for another huge year!

04.01.2022 Quick engine bay tidy up for @65anml mustang!

04.01.2022 Congratulations to Jono Danaskos with his beautiful mustang we had a hand in building.. Tubbed, moved springs, shorten diff and boot floor for phase 1 then it got a make over a few years later, we smoothed the engine bay for his super clean engine and accessories to be bolted back in. Well kept car that gets driven hard! Well deserved!

04.01.2022 A piece of @warspeed_industries art going into this VX clubsport to wake it up! Turbo pipes from @killaboost_manifolds Look at the bronze from @shaunscustomalloy aswell..... @imperial_bodyworx painted the smoothed bay.. Tubbed, plumbed, wired and tuned in house! Long time coming but this will be a cool cruiser!

04.01.2022 Another one done! VL tubbed and sheeted running one of our rear end kits including 9housing, arms, coilovers and all bracketry All Powdercoated Fuel cell through the floor to existing fuel system ... Wilwood brakes all round See more

03.01.2022 Mustang tubbed for 295s A few of our little tweaks and we have plenty of clearance, factory style fuel tank cut and shut to suit the new floor..

03.01.2022 What a tough street car! No tubs No Simmons No candy paint or cream leather..... Just straight up all motor (and blower) old school tough Came in for a set of caltracs

02.01.2022 Genuine xb GT came in with the undercarriage all colour coded to the body.. but original is black.. so we had the meticulous task or removing most easy parts and masking up the rest and give it a fresh coat of black. Big difference and will now look closer to concourse restoration .. The foil is a nice trick I learnt from a painter and will always use it saves so much time in masking and removal is even easier

02.01.2022 VKBROK now with a smoothed bay, our custom pwr radiator, shroud and fans Brake lines and tucked wiring in-house Prepped and painted by the @imperial_bodyworx ... Off to @hitorqueperformance for the killer engine to be fitted up.. wait for this one! Putting a spin on the normal brock blue and black @pwrperformanceproducts @imperial_bodyworx

02.01.2022 We had @bom.88a come in for a revamp of the engine bay and a few things underneath he wasnt happy with.. Up there with one of the most modified ve engine bays now.. deleted guard bolts, built in breather tanks, smoothed sides, sheeted in radiator and headlights, flat firewall, under dash pedal assembly, modified acc pedal, all the things you dont notice are all done too ... Once the paints laid on it and the @warspeed_industries engine is back in, be sure to look out for it! See more

02.01.2022 This Vk now rolling on some @simmonsaustralia Housing was supplied but we did lower bracketry, coilover mounts and Custom adapters made all round.. Good to see the cars roll out and be onto the next stage of their life Before being raped and repeat ... #simmons #bluevk #brock #ultimatemetalworks See more

01.01.2022 This thing is tough as nail! Cant beat the sound of a 355 stroker.. Tubbed for the new @simmonsaustralia fr1 flow formed rims Coilovers Tube arms... Shorten diff Billet axles Flat spare wheel Rear Tunnel section.. #ultimatemetalworks See more

01.01.2022 Heres another engine bay on a VK we did a full fab build on.. @warspeed_industries engine package @killaboost_manifolds @plazmamanracing cooler & clamps... @shaunscustomalloy manifold @imperial_bodyworx on the spray gun again to lay down the @dnapaints orange See more