Infinity Innovation & Design in Dalyellup | Boat service

Infinity Innovation & Design

Locality: Dalyellup

Phone: +61 448 351 460

Add/Update information

Reviews

Tags

• Engineering service
• Automotive, aircraft & boat
• Designer
• Boat service

25.01.2022 Less drag and rotational inertia in your Jetpump. This is and experiment for a Seadoo RXP. Almost 117gms less than OEM.

25.01.2022 Seadoo RXP Jetpump rebuild #2ID #jetpump #jetski #PWC #RebuiltinWA

24.01.2022 Seadoo Jetpump fixture ready for use. Repairing the seal area. Initial setting up of housing and then onto check for how True it is concentrically to the bearing bore.

24.01.2022 Update on the Yamaha Jetski blown engines The individual rod ends are not the same from factory, both small and large ends of both sets vary in mass. One engine has aftermarket pistons the other OEM. Both sets of rods have the same markings S, T & R yet different weights. Piston speeds <4000Ft/Min... Pistons good for 10526 rpm = 3999.88 Ft/Min So why did the rods let go??? Can it be the rod bolts? One set still has the bolts but a snapped rod. The other set has a full rod but a snapped rod big end minus the cap?

23.01.2022 Had a client drop in for some Turbo repair help. GT28. Most of the info I saw was using a hammer to part the exhaust snail shell from the centre bearing unit. I prefer to use a puller with no effort. #2ID #rebuiltinwa #manufacturedinwa #aussiemade #GT28 #turbo #turborebuild

22.01.2022 Crankshaft installed, caps tightened down with Plastigauge underneath and first check of bearing clearances completed. Some customising required on 1 & 2 (close up clearance) and 4 & 5 (open up tolerance)to get them all the same. Final checks completed and all bearing clearances now with desired spec. Endfloat check also completed and within tolerance.... #2ID #Holden355 #enginerebuild

22.01.2022 Test run of the overhauled Seadoo RXP Jetpump. See us for your next Jetski service, Supercharger overhaul, Jetpump rebuild. We also do the following... Code clearing if you do the maintenance work yourself. Key programming and removal New key fob programming for the Yamaha skis Engine rebuild and any other maintenance #2ID #PWC #jetpump #jetski #manufacturedinwa #seadoo

22.01.2022 Tack soldered and ready for a final check on removal for more soldering required.

21.01.2022 Look Mum no hands!!!!! Not a bad fit. Roughing out the jig to hold the Seadoo Jetpump housing. Why, because I need to fix the seal area of this pump.... #2ID #jetpump #PWC #jetski

21.01.2022 Final operational check of the Seadoo RXP Jetpump prior to install. #2ID #PWC #jetpump #jetski #rebuiltinwa

19.01.2022 2 separate Yamaha Jetski engines blocks, from different Jetskis, similar damage at opposite ends of the crankcases. One is definitely missing a piston and part of the rod Why is this so???????? Thats what I want to understand. Is it piston length vs diameter? Piston flutter/ slap at high revs? Why well I have a Yamaha KT100s rod and piston and the piston is a smaller bore (100cc) and longer piston overall. ... Yes I know the KT100S is a piston port engine, none the less something is not right. I have another new engine that has had the piston leave the rod, yet Conrod and gudgeon pin still attached. #2ID #jetski #PWC #yamahajetski #waverunner #pwcengine #rebuiltinwa

19.01.2022 No burrs or casting flash on this Jetpump anymore. Just how it should be.

18.01.2022 Some deep corrosion inside the seal area of the Seadoo Jetpump. Need to clean out the rot and make it like new. #2ID #pwc #Jetpump

17.01.2022 Quality over price. I will only use top quality manufactured parts for my clients JetSki repairs. Japanese NSK bearings that we know are top quality and will go the distance.

16.01.2022 Final mockup of the Holden 355 Stroker Priority Mains Oiling lines and checking clearance under the manifold prior to brazing. Then a final check to test flow out of each line to make sure there are no obstructions. #2ID #Holden355 #Prioritymainsoiling #oilmods

15.01.2022 Our order for new copper fittings has arrived and now we can start the design, bend and install process mock up.

14.01.2022 Modifications to a clutch hub to suit a new motor for a customer. #2ID #manufacturedinwa #aussiemade #rebuiltinwa #smallengine

13.01.2022 Finally after 6 weeks I finally got the Acme tap. 2ID-ITB-001 is completed. Full upload of Design Concept - to completed bends

13.01.2022 We got some 2ID-PCSS made to our specs. This one is for a Barra Crank. Gotta Keepem separated long term storage solutions. Put on some Desno tape or other long term protective coating and then its ready to use when ready. No rust or dust or damage to your expensive crankshaft while doing the rest of your build.

13.01.2022 Setting up the Seadoo Jetpump housing for machining and repairing the seal area. Facebook only lets you post one video at a time. How about fixing that Zuckerberg!!!!! #2ID #jetski #jetpump #PWC

13.01.2022 Some pics of our WA Designed and Manufactured Degree Wheel. P/N# - 2ID-600DW-001 Crane cams - 276mm OD... 2ID - 600mm OD Made from 6mm Stainless steel Laser etched.

12.01.2022 Seadoo RXP Jetpump rebuilt and ready for install. See us for your next Jetski service, Jetpump rebuild or supercharger overhaul or service. All makes all models.... #2ID #jetski #jetpump #PWC #rebuiltinwa

12.01.2022 2ID-HV8-001 Holden crankshaft to 2ID-600DW-001 adaptor. Fits like the proverbial now need to bore and key to suit the crank.

12.01.2022 2ID-HV8-001 (Holden crankshaft adaptor) & 2ID-600DW-001 (600mm Degree Wheel) mated together as one on the crankshaft #2ID #degreewheel #enginerebuild #holden355 #rebuiltinwa

09.01.2022 New Jetpump seal vs old seal (now in pieces) so I can see how it is made:):):):):) dual excluder PTFE seals inside a stainless case.

09.01.2022 Our new 2ID designed Cam Degree wheel (2ID-600DW-001) has arrived. Designed by us in SolidWorks Cut from 6mm Stainless - No rusting Laser etched .2mm... Made in WA #2ID #ManufacturedinWA #degreewheel

09.01.2022 Washing the piston assemblies prior to Mockup of the engine. Most people have a six pack of cans but I like to do better than that! I have an Eight Pack in my esky!!!!... #2ID #rebuiltinwa #manufacturedinwa #aussiemade #355Holden #eightpack

07.01.2022 Video showing the setup of our WA Designed 2ID-600DW-001 600mm Cam Degree wheel. Made from 316SS 6mm thick Laser etched... #2ID #manufacturedinwa #degreewheel #aussiemade

06.01.2022 The importance of doing Jetpump maintenance assists long term reliability. Dry burnt grease does little to assist the rubber seals in preventing ingress of water.

05.01.2022 2ID-HV8-001. Now for a trial fit on the crank snout.

03.01.2022 Just to show not everything goes according to plan. I was experimenting with a new concept of using an induction cooktop to heat some Conrods, besides smelling like fish and chips the temp got close to 230C but no cigar.

03.01.2022 The 355 Holden stroker out for its last wash prior to a mock buildup. While washing it we also tested the priority mains oiling to check for flow. Thankfully the oil pump will have more pressure than our suburbs mains pressure. No leaks on the oil line system. Dont mind the big threaded plug at the end of the video, it will be the same as all of the others.

02.01.2022 Got some feedback on the latest overhaul of the Seadoo Jetpump from the owner. He took it out straight after picking it up. Feedback good or bad is always a positive. Feedback allows for continual improvement of knowledge and service provided.... It allows you to understand what went right, go back over your notes, recheck photos and improve processes and procedures. Differences between manufacturers and also to future parts purchases on preferred vendors. #2ID #seadoo #jetski #jetpump #pwc #rebuiltinwa

01.01.2022 Washing and storing the 355 Holden stroker ring stacks prior to final assembly. #2ID #aussiemade #manufacturedinwa #355holden #rebuiltinwa #eightpack

01.01.2022 Seadoo Jetpump liner removed. Left in the bar fridge overnight and The magic happens it just comes out by hand.

01.01.2022 Jetski Jetpump rebuilding is not just the impellor, shaft and bearings. WE also check over and replace the nylon, bronze or stainless bushes in the linkages as required.