Tas Aqua Engineering in Cambridge, Tasmania, Australia | Local business
Tas Aqua Engineering
Locality: Cambridge, Tasmania, Australia
Phone: +61 438 750 160
Reviews
to load big map
22.01.2022 Tank Fit Out for large industrial site near Launceston, 315mm Stubs and Galvanised Backing Rings. We travel anywhere, no job to small or to big!
22.01.2022 Here is some Dam Liner work that we carried out for a customer, the original was leaking so we laid a sheet of material over the area and rewelded it to the Liner and around the outlet.
22.01.2022 Here is a Poly Macerator Tank that we made for a customer this week to go into a boat, the top has had stainless steel helicoils installed for a lid to be bolted down and seal the unit.
22.01.2022 Here is a little Pipe job we did for a customer a few weeks ago from 110mm Poly. We had to divert an existing line than ran straight up the wall and run it around the outside of the building. We also installed a Scour Valve so that the line can be flushed, we installed a 1 Way Wafer Check Valve to prevent water back wash through an existing line and contaminating and then connected to an existing PVC line.
22.01.2022 Here's some Poly Water Tanks that we fitted out for a customer last week, 90mm Stubs and Galvanised Backing Rings in all tanks.
21.01.2022 Here's some recent work carried out for a customer with pipework setup ready for irrigation. All secure and protected!
21.01.2022 Here are some custom Tanks and Pipework we carried out for a customer last week. We made up goose neck air vents with vermin screens for ventilation and also installed a 160mm deodorizing line.
21.01.2022 Here we have done some mains pipework with spigots coming off ready to be plumbed into tanks once the tanks have been built, all spigots have been strengthened with extra lugs welded around...it's the little things that count for a great job!
20.01.2022 We are looking for an experienced poly welder to join our team. Must be motivated and have great problem solving skills. $45 per hour casual rate for the right applicant. If you have what it takes a permanent position is a possibility. Email [email protected] or message me through this page if you are interested. Can everyone please share this to get the word out there.
20.01.2022 Here is a kilometre of pipeline ready to be joined and sunk from a recent project,
17.01.2022 We did this Custom Tank and Piping job last week for a customer which included Poly, Ductile and PVC. We installed mains water lines, leveling pipes between the tanks, overflows and scour and valves.
14.01.2022 Another couple of custom tanks fitted out last week!
13.01.2022 Here are some large custom poly battery boxes made recently.
13.01.2022 Some recent Dam and Irrigation work we did. Poly Strainer for dam wall, air valves and water valves.
12.01.2022 Another Tank Fit Out job...one of our specialties. Any custom design/work is not a problem!
12.01.2022 Most of what we do doesn't get seen. This coupler that was installed by another company was found to be leaking in the middle of a seed crop. We were called in to make an emergency repair until the seed is taken off then we will replace the section of pipe.
06.01.2022 Custom pipework carried out on a job before Xmas, bit of a jigsaw puzzle...but nothing we can't do!
04.01.2022 Here is a recent Slimline Tank fit out we did for one of our customers. The tanks were fitted out with 2" & 1" spin weld BSP threads, 4" BSP Threads, Inspection Openings were capped off and BSP threads inserted and overflows were capped with PVC stops.
03.01.2022 Here is another custom tank fit out we did last week, all stub flanged fittings.
02.01.2022 Here is some custom made Poly Duct Work made recently, it was made from 10mm thick material and to suit square to round.
01.01.2022 FOR SALE Marine Floats $100 each. Used but in excellent condition, approx. 150 off in Black and Yellow. 290 Litres, 1350mmL x 700mmW.
